Az ICP DAS holdújév miatt leállása 2023 január 20-29. között lesz, ez kis mértékű szállítási késedelmeket fog okozni a januári megrendeléseknél  az EU raktárról nem szállítható termékek esetén. Elnézést kérünk a kellemetlenségért! 

Az év eleji jó hírünk hogy több száz kedvelt ICP DAS termék ára csökkent valamint ezen kívül  január 09.-től még évkezdő akciók is indulnak. Konverterek, átjárók, IO eszközök, Ethernet switchek és még sok más termék.

Az akciós termékeket ide kattintva találják.

ICP DAS HUNGARY

309464608

ICP DAS HUNGARY
  • Kategóriák
    • Újdonságok 
    • Akciók 
    • Raktáron (szállítás 2-4 nap) 
    • Konverter, vonalerősítő, hub  
    • Soros - Ethernet konverter, szerver, RS-232, RS-422, RS-485  
    • Ethernet switch 
    • RS-485 portos terepi I/O [Modbus, DCON] 
    • Ethernet I/O modulok 
    • USB I/O modulok 
    • Profibus [konverter, vonalerősítő, átjáró, I/O, csatlakozó, kábel] 
    • Modbus modulok 
    • PAC - PLC - Érintőképernyős PLC - HMI 
    • CAN, CANopen, DeviceNet terepi I/O modulok, konverterek, átjárók, PC kártyák 
    • SAE J1939 modulok 
    • HART modulok 
    • EtherNet/IP modulok 
    • BACnet/IP modulok 
    • BACnet MS/TP modulok 
    • PROFINET modulok 
    • EtherCAT modulok 
    • M-Bus [Meter-Bus] és Wireless M-Bus [W-MBus] modulok és konverterek 
    • DALI (Digital Addressable Lighting Interface) 
    • Data Highway Plus 
    • PLC programozó kábel, kiegészítő és szerszámgép kábel a legtöbb ismert márkához 
    • ICP DAS Bővítő kártyák # X-Board, XV-Board, XW-Board 
    • Jelkondícionáló modul 
    • Ipari Panel PC 
    • Ipari számítógép és tartozék (PC, Notebook, Tablet, Mini PC, stb.) 
    • Ipari notebook és tablet 
    • Ipari és kereskedelmi monitor 
    • HMI kijelzők 
    • WiFi eszközök 
    • Fogyasztásmérés, PMMS, mérőleolvasás, teljesítménymérő gyűjtés 
    • Hőmérséklet, páratartalom, megvilágítás mérés, adatgyűjtő 
    • Industrial Internet of Things (IIoT) [MQTT protokoll] 
    • GSM, GPRS, SMS, GPS, M2M 
    • Rádió modem [RF modem, LoRa modem, WiFi modem] 
    • ZigBee termékek 
    • Modbus rádió modemek, RF, 868 MHz, LoRa 
    • LoRaWAN eszközök 
    • SIGFOX eszközök 
    • Bluetooth 
    • Infra port, IrDa 
    • Ethernet média konverter, extender 
    • Touch Pad 
    • Optikai leválasztó, szigetelő, villám és túlfeszültség védelem 
    • Motion és gépadat gyűjtés, vibráció analízis 
    • PC és külső bővítő kártyák - adatgyűjtés, I/O és interfész (PCI, UPCI, ISA, PCI Express, stb.) 
    • Épület és Home automatizálás 
    • KNX termékek 
    • Video audio jeltovábbítás és szétosztás, KVM, stb 
    • USB Floppy Emulátor 
    • Kiegészítők (kábel, csatlakozó, stb.) 
    • Tápegységek 
    • Automatizálás, vezérlés, szabályozás eszközei 
    • Machine Vision ipari kamerák és tartozékok 
    • LonWorks 
    • Outlet  
    • Kifutott termékek (EOL) 
  • GYÁRTÓK
    • ICP DAS
    • Adeunis
    • MOXA
    • ATEN
    • LANTRONIX
    • COMNET
    • TRENDNET
    • ATOP
    • SCUDENO
  • RS-232/422/485 KISOKOS
  • GYIK
  1. OMRON
  1. PLC programozó kábel, kiegészítő és szerszámgép kábel a legtöbb ismert márkához
  2. OMRON

FS-CIF11 # OMRON CPM1A/2A-CQM1/C200H megfelelő programozó interfész modul

Cikkszám:
FS-CIF11
FS-CIF11 #  OMRON CPM1A/2A-CQM1/C200H megfelelő programozó interfész modul
  • FS-CIF11 # OMRON CPM1A/2A-CQM1/C200H megfelelő programozó interfész modul
    FS-CIF11 # COMPATIBLE WITH CPM1-CIF11/CIF12,THE PERIPHERAL PORT AND RS232 TO RS422/485 INTERFACE MODULE FOR OMRON PLC,IT CAN USE FOR CPM1A/2A,CQM1,C200H Α ETC SERIES PLC

 

 

Nem vásárolható!
  • Részletek
  • Adatok
Részletek

FS-CIF11 is the peripherals port  and RS232 to RS422/485 interface module that is developped for Omron PLC . Its functions include more than Omron’s CPM1-CIF11 (peripheral mouth to  RS422), CPM1-CIF12 (peripheral mouth to RS485), NT-AL001 (RS232 to RS422), 3G2A9-AL004-E (RS232 to RS422) module. It uses for CPM1A/2A, CQM1, C200H α series PLC, and it can connect PLC peripherals mouth or RS232 communication mouth (automatic identification), the output is RS422 (4-wire full-duplex) or RS485 (second-line half-duplex). The product without an external power supply, communication distance can be up to two kilometers.

Below are the FS-CIF11 and Omron CPM1-CIF11 and NT-AL001 comparison:

 

 

       Module

function

FS-CIF11

CPM1-CIF11

CPM1-CIF12

NT-AL001

3G2A9-AL004-E

PLC and the connector

 peripherals

interface 、RS232

Peripherals interface

 

Peripherals interface

RS232

And computer ports

RS232

No

No

RS232

Output interface

RS422和RS485

RS422

RS485

RS422

An external power supply

No

No

No

Need an external power supply

Communication transceivers indicator

Yes

No

No

No

The greatest distance

2000m

500m

500m

500m

The largest group site points

32

32

32

32

 

Technical details: 
1, peripheral mouth, RS232 serial port and computer and other equipment Serial RS232 which can connect with the PLC 
2, outputting is the four-full-duplex RS422 interfaces and second-line half-duplex RS485 interfaces 
3, no external power 
4, communication lines choose the unshielded twisted pair which cut-off area is over 0.5 mm2 
5, the largest communication distance is 2,000 meters 
6, the largest group site points is 32(the hardware of the product itself can support 128 sites) 
7, the largest communication rate is 115.2 Kbps, baud rate adaptive 
8, a transient voltage suppression, can withstand the power of up to 400 W transient over-voltage, to mine, and the impact of electrostatic discharge 
9, work temperature: -20 ~ 70 ℃ 
10, installation: 35 mm standard rails installed and the installation bolt hole 
11, Dimensions: 85 × 55 × 25

 

PERIPHERAL/RS232 socket(DB9M)signal definition

 

 

Pin number

Signal name

description

1

+5V

External connect 5v assistant power supply, not used

2

RXD

RS232 signal receive

3

TXD

RS232 signal send

4

DTR

Get data terminal ready

5

GND

Signal ground

6

DSR

Get data device ready

7

RTS

Request send

8

CTS

Allow to send

9

Not used

Not used

 

Signal definition of RS485/422 connection terminal

 

 

Signal name

description

B

RS485 signal, positive

A

RS485 signal, negative

SDB

RS422 signal sending, positive

SDA

RS422 signal sending negative

RDB

RS422 signal receiving, positive

RDA

RS422 signal receiving, negative

SG

Signal ground

FG

Shield ground(chassis ground)

 

FS-CIF11 and PLC or computer connections: 
    All the connections of FS-CIF11 and the PLC peripheral mouth, RS232 Serial and computer RS232 serial port use PERIPHERAL/RS232 socket (DB9M). The products internal circuit will automatically identify the peripherals and RS232 serial peripherals. With the use of peripheral connection cable which products equipped can connect the FS-CIF11 to Omron CPM1A/2A, CQM1, C200H α, and other PLC peripherals directly. The connection cable of FS-CIF11 and PLC RS232 Serial or computer RS232 need users to make, referring to follow pictures. If use the shielded cable, please weld the shield layer on the cover of the two plugs.

The application of products:

    The use of FS-CIF11 adapter can connect  up to 32 Omron CPM1A/2A, CQM1, C200H α and other PLC  as -RS485/422 top communications network ,and connect PLC peripherals mouth, RS232 serial port or both mixed-use, the communication distance can be up to 2,000 meters. Connect shield with the FS-CIF11 "FG" on the terminal when use unshielded twisted pair.

1,second-line half-duplex RS485 communications network:

    Turn  the RS485 and RS422 selection switch K1 on the FS-CIF11 adapter to "485", and turn the terminal resistance setting switch K2 on the FS-CIF11 of the network start and end to "R", and turn the terminal resistance setting switch K2 on other FS-CIF11 of the network to "OFF".

 

2, 4-wire full-duplex RS422 communications network 
This way equals to Omron CPM1-CIF11 and NT-AL001. 
Turn the selection switch K1 on the RS485 and RS422 of FS-CIF11 adapter to "422", turn the terminal resistance setting switch K2 on the  FS-CIF11 of the network start and end to "R", turn the terminal resistance setting switch K2 on other FS-CIF11 of the network to "OFF".

 

NOTES: 
1, the communication lines should choose the unshielded twisted pair which cross-sectional area should be more than 0.5 mm2 and 120-ohm impedance. 
2, in order to prevent RS485/422 interface of the common mode voltage impact beyond the permitted range and even damage the reliability of communication interfaces,  low resistance wires which cross-sectional area is 1 mm2 can be used to link up the signal ground “SG” of all FS-CIF11 to eliminate the potential difference between all nodes on the network. 
3, the cable length(extension)of all FS-CIF11  to the bus can’t be over 15 meters, otherwise they will have echoes, affecting the normal communications of the system. The best option is connecting FS-CIF11 with the RS485/422 bus directly. 
4, about the settings of the terminal resistance, the function of the terminal resistance is to eliminate the waveform distortion caused by the signal reflection in the communication lines , turn the termination resistor setting switch K2 on the FS-CIF11 on the communication lines start and end to "R" (access terminals 120EU resistance), and turn the resistance setting switch K2 on other FS-CIF11 of the communication lines to "OFF" (not-to-end resistance). 
5, when the communication procedures used at full-duplex mode, can only use four-full-duplex RS422 connection; when the communication procedures used half-duplex mode, they can use second-line four-or half-duplex RS485 full-duplex RS422 connection. Please refer to PLC use manuals, communication manuals and other related information about programming. 
6, when connect the RS232 serial port, if your RS232 is no power serial port or the output current is small(as some PDA), you can add i5 V auxiliary power between 1pin and 5pin on the DB9 outlet of the FS-CIF11, 1pin to straight. 5pin to negative. 
7, Annex: equip a peripheral connection cable with product

Megj.: Kiváló minőségű OEM termék, de nem eredeti OMRON gyártmány.


 

  s!nus-elektrotechnikai bt.

  Industrial IT & Automation

 

25 éves jubileum / 25 th Anniversary

 www.s-e.hu    #    www. icpdas.hu

Email: info@s-e.hu    #   Tel:  96/525530    #    Fax: 96/525531    #    Mobil: 30/9464608 

 

RS-232, RS-422, RS-485 konverterek, Ethernet konverterek, RS-485 I/O, Modus I/O, Soros-Ethernet konverterek, USB I/O, Ethernet I/O, Profibus, M-bus, Rádió modem, Ethernet switch, CAN, CANopen, DeviceNet, Profinet, HART, BACnet, EtherCAT, EtherNet/IP, Wireless MBus, DALI, ZigBee, LoRaWan, SIGFOX, IoT, TouchPAD  Fogyasztásmérés és leolvasás  USB konverter  ICP DAS HUNGARY

RS-232 - WiFi konverter, RS-485 - WiFi konverter,

ICP CON konverter    USR IOT konverter

 

Sinus-Elektrotechnikai Bt.   ICP DAS HUNGARY

RS-232 konverter, RS-422 konverter, RS-485 konverter, RS-485 repeater, USB konverter, Soros Ethernet konverter, RS-232 Ethernet konverter, RS-422 Ethernet konverter, RS-485 Ethernet konverter, Ipari Ethernet switch, Managed DIN switch, PAC, PLC, HMI, Programozó kábel, Ipari monitor, Ipari éritőképernyős monitor, Ipari PC, Ipari laptop, Ipari tablet, Ipari panel PC,  Barebone PC, Mini ITX PC, RS-485 I/O, Profibus I/O modul, Profibus gateway, Profibus konverter, Profibus átjáró, Profibus csatlakozó, Modbus I/O, Ethernet I/O, Modbus gateway, CAN konverter, CAN I/O, CANopen konverter és I/O, DeviceNet konverter és I/O, Hart konverter, Ethernet/IP modul és konverter, BACnet/IP modul és konverter, PROFINET konverter, I/O modul, EtherCAT modul, M-Bus modul, konverter, DALi modul, DALI konverter, PLC programozó kábel, Siemens programozó kábel, WiFi I/O, GSM modem, GPRS modem, SMS küldő, ZigBee konverter, ZigBee I/O, Bluetooth modul, LoRaWAN modul, SIGFOX Modul, IIoT MQTT modul, Média konverter, Touch Pad, Optikai leolvasófej, Analóg, Digitális, Soros PCI kártyák, Épület automatizálás, Ipari tápegység, Ipari kamera, MachineVision, Fogyasztásmérés és elemzés, Földrengés előjelzés, Adatgyűjtés eszközei,  Rezgés elemzés, konverter és repeater, Profibus kábel, Profibus csatlakozó, Soros RS-232 RS-485 WiFi konverter, Ipari Gigabit Ethernet switch, WiFi i/o modul, IEC 1107 mérőleolvasás, Optikai leolvasó fej ICP DAS, ICPDAS, ICP CON, MOXA, ADEUNIS, USR IOT, IEI, B+B SmartWorx, ELKO EP, EXSYS, LILLIPUT, STARTECH, PATTON

All product names, trademarks, brands and logos used on this site are the property of their respective owners. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorisation by any rights holder.

 

© 2018-2022  Sinus-Elektrotechnikai Bt.  Minden jog fenntartva.

A műszaki adatok és információk előzetes értesítés nélkül megváltozhatnak.

 

Adatok
Gyártó:
NONAME OEM
Vásárlói fiók
  • Belépés
  • Regisztráció
  • Profilom
  • Kosár
  • Kedvenceim
Információk
  • Általános szerződési feltételek
  • Adatkezelési tájékoztató
  • Fizetés
  • Szállítás
  • Elérhetőségek
Sinus-Elektrotechnikai Bt.
  • 9028 Győr, Móra tér 17.
  • 309464608
  • info@s-e.hu
  • Személyes áruátvétel előzetes bejelentkezéssel:
  • 9028 Győr, Ötház utca 34.
Iratkozzon fel hírlevelünkre!

Értesüljön az elsők között az újdonságokról és az aktualitásokról.

Feliratkozás
SSL Certificate
  • Újdonságok 
  • Akciók 
  • Raktáron (szállítás 2-4 nap) 
  • Konverter, vonalerősítő, hub  
  • Soros - Ethernet konverter, szerver, RS-232, RS-422, RS-485  
  • Ethernet switch 
  • RS-485 portos terepi I/O [Modbus, DCON] 
  • Ethernet I/O modulok 
  • USB I/O modulok 
  • Profibus [konverter, vonalerősítő, átjáró, I/O, csatlakozó, kábel] 
  • Modbus modulok 
  • PAC - PLC - Érintőképernyős PLC - HMI 
  • CAN, CANopen, DeviceNet terepi I/O modulok, konverterek, átjárók, PC kártyák 
  • SAE J1939 modulok 
  • HART modulok 
  • EtherNet/IP modulok 
  • BACnet/IP modulok 
  • BACnet MS/TP modulok 
  • PROFINET modulok 
  • EtherCAT modulok 
  • M-Bus [Meter-Bus] és Wireless M-Bus [W-MBus] modulok és konverterek 
  • DALI (Digital Addressable Lighting Interface) 
  • Data Highway Plus 
  • PLC programozó kábel, kiegészítő és szerszámgép kábel a legtöbb ismert márkához 
  • ICP DAS Bővítő kártyák # X-Board, XV-Board, XW-Board 
  • Jelkondícionáló modul 
  • Ipari Panel PC 
  • Ipari számítógép és tartozék (PC, Notebook, Tablet, Mini PC, stb.) 
  • Ipari notebook és tablet 
  • Ipari és kereskedelmi monitor 
  • HMI kijelzők 
  • WiFi eszközök 
  • Fogyasztásmérés, PMMS, mérőleolvasás, teljesítménymérő gyűjtés 
  • Hőmérséklet, páratartalom, megvilágítás mérés, adatgyűjtő 
  • Industrial Internet of Things (IIoT) [MQTT protokoll] 
  • GSM, GPRS, SMS, GPS, M2M 
  • Rádió modem [RF modem, LoRa modem, WiFi modem] 
  • ZigBee termékek 
  • Modbus rádió modemek, RF, 868 MHz, LoRa 
  • LoRaWAN eszközök 
  • SIGFOX eszközök 
  • Bluetooth 
  • Infra port, IrDa 
  • Ethernet média konverter, extender 
  • Touch Pad 
  • Optikai leválasztó, szigetelő, villám és túlfeszültség védelem 
  • Motion és gépadat gyűjtés, vibráció analízis 
  • PC és külső bővítő kártyák - adatgyűjtés, I/O és interfész (PCI, UPCI, ISA, PCI Express, stb.) 
  • Épület és Home automatizálás 
  • KNX termékek 
  • Video audio jeltovábbítás és szétosztás, KVM, stb 
  • USB Floppy Emulátor 
  • Kiegészítők (kábel, csatlakozó, stb.) 
  • Tápegységek 
  • Automatizálás, vezérlés, szabályozás eszközei 
  • Machine Vision ipari kamerák és tartozékok 
  • LonWorks 
  • Outlet  
  • Kifutott termékek (EOL) 
  • GYÁRTÓK
    GYÁRTÓK
    • ICP DAS
    • Adeunis
    • MOXA
    • ATEN
    • LANTRONIX
    • COMNET
    • TRENDNET
    • ATOP
    • SCUDENO
  • RS-232/422/485 KISOKOS
  • GYIK
Pénznem váltás
Belépés
Regisztráció
oogle
Kosár
A kosár üres. Vásárláshoz kattintson ide!
Cookie beállítások
Weboldalunk az alapvető működéshez szükséges cookie-kat használ. Szélesebb körű funkcionalitáshoz marketing jellegű cookie-kat engedélyezhet, amivel elfogadja az Adatkezelési tájékoztatóban foglaltakat.